X5000 Mac addresses

AmigaOne X5000 platform specific issues.

X5000 Mac addresses

Postby Tijatjj » Thu Jun 06, 2019 8:52 pm

Hi is there any way to install MAC address as mine were lost when I had to redo the sd card shows blank after reset of Mac address Thanks
Tijatjj
 
Posts: 82
Joined: Tue Sep 04, 2018 5:12 am

Re: X5000 Mac addresses

Postby msalcedo » Fri Jun 07, 2019 5:16 am

to reset your MAC address after flashing the firmware using the uboot prompt..

Setenv eth1addr xx:xx:xx:xx:xx:xx
Setenv eth2addr xx:xx:xx:xx:xx:xx
Saveenv

you did write down the addresses?

Don't forget at uboot prompt type "help" and get all the commands
User avatar
msalcedo
Beta Tester
Beta Tester
 
Posts: 88
Joined: Fri Oct 21, 2011 12:55 am
Location: Sacramento, CA USA

Re: X5000 Mac addresses

Postby Tijatjj » Fri Jun 07, 2019 5:42 am

Some one mentioned that they are printed in the corner of the board I hope.
Tijatjj
 
Posts: 82
Joined: Tue Sep 04, 2018 5:12 am

Re: X5000 Mac addresses

Postby Skateman » Wed Jun 12, 2019 5:33 pm

Tijatjj wrote:Some one mentioned that they are printed in the corner of the board I hope.


No, the newer batches of boards dont have the mac addresses printed on there..so what u need is:

Boot the system with an Old U-Boot version. This version will probe the HW macs.Write them down. Insert the newer U-Boot SD and program them as mentioned above.

I have also found out the hard way, see my ticket below... ps the links dont work anymore..

Date Submitted: Tuesday 23 January, 2018

The comments for your ticket are as follows:

Hi,

Sorry for delay,

Ok, you need Win32 Disk Imager. Please download that on your PC.
One downloaded, run and insert your SD card. Download and unzip this file;

http://technical.leamancomputing.com/Te ... s_5020.zip <---------OLD FIRMWARE
http://technical.leamancomputing.com/Te ... 7-4-17.zip <---------CURRENT FIRMWARE

Extract and point Win32 Disk Imager to the bin file. Then click "WRITE". Make sure you have the correct drive selected before pressing "WRITE".

Once its written, place in motherboard. Boot, go to Startup Menu and select system info. It will display MAC addresses (stored internally in chips). Note them down. Power down and insert old SD card.
Boot back up and go into Startup Menu and select "Command Line". Now type; set ethaddr "YOUR NOTED MAC ADDRESS" press return to temp store command, then do same for ethaddr1. Once done. Type saveenv and then press enter. It should now permanantly store the values.

You can check by typing printenv and then press Retur n. It should have MAC addresses stored.


**DO NOT REPLY TO THIS EMAIL- USE THE SUPPORT TICKET SYSTEM TO ADD COMMENTS**
AmigaOne X5000 -> 2GHz / 16GB RAM / Radeon R7 250 / M-Audio 5.1 -> AmigaOS 4.1 FE / Ubuntu Linux
Amiga 1200 -> Recapped / 68ec020 ACA 1221ec / CF HDD / RetroNET connected to the world
User avatar
Skateman
 
Posts: 374
Joined: Thu Aug 10, 2017 9:36 pm
Location: The Netherlands

Re: X5000 Mac addresses

Postby Tijatjj » Thu Jun 13, 2019 4:23 am

Oh boy thanks
Tijatjj
 
Posts: 82
Joined: Tue Sep 04, 2018 5:12 am

Re: X5000 Mac addresses

Postby khayoz » Wed Jun 26, 2019 9:50 am

@Skateman
What´s new in the latest X5000 firmware?
Where do I get it?
1989-> A500, A600, A3000, A4000, A1200, CD32, µA1, PegII, A1XE, CDTV, Amy/416D79 Prototype, A1X5000, Vampire 500 V2+, Vampire 600 V2, Amy-ITX <-2018
User avatar
khayoz
 
Posts: 10
Joined: Sun Jan 08, 2017 6:24 am
Location: Stockholm, Sweden


Return to Platform: AmigaOne X5000

Who is online

Users browsing this forum: No registered users and 1 guest