Page 1 of 1

Preparing a new HD for installing 0S4.1 FE

Posted: Fri Aug 18, 2017 2:01 pm
by JosDuchIt
Guidance on this? URL?

When on mediatoolbox you hit install, then on rdb editing install again you are asked to select AmigaOne boot code
= SLB—v2 ?

Re: Preparing a new HD for installing 0S4.1 FE

Posted: Fri Aug 18, 2017 3:57 pm
by xenic
JosDuchIt wrote:Guidance on this? URL?

When on mediatoolbox you hit install, then on rdb editing install again you are asked to select AmigaOne boot code
= SLB—v2 ?
I would also like to know the answer to that for X5000. Some systems have SLB, X1000 has amigaboot.of and I don't see any boot file for X5000.

Re: Preparing a new HD for installing 0S4.1 FE

Posted: Fri Aug 18, 2017 5:23 pm
by Spectre660
Yes for Sam440 and Sam460 .
JosDuchIt wrote:Guidance on this? URL?

When on mediatoolbox you hit install, then on rdb editing install again you are asked to select AmigaOne boot code
= SLB—v2 ?

Re: Preparing a new HD for installing 0S4.1 FE

Posted: Fri Aug 18, 2017 5:24 pm
by Spectre660
for X5000 the boot code is on the microsd card .
(X5000 manual page 10)
xenic wrote:
JosDuchIt wrote:Guidance on this? URL?

When on mediatoolbox you hit install, then on rdb editing install again you are asked to select AmigaOne boot code
= SLB—v2 ?
I would also like to know the answer to that for X5000. Some systems have SLB, X1000 has amigaboot.of and I don't see any boot file for X5000.

Re: Preparing a new HD for installing 0S4.1 FE

Posted: Tue Aug 22, 2017 6:49 pm
by xenic
Spectre660 wrote:for X5000 the boot code is on the microsd card .
(X5000 manual page 10)
In that case, what do you enter for AmigaOne boot code in the Edit RDB window of MTB??

Re: Preparing a new HD for installing 0S4.1 FE

Posted: Tue Aug 22, 2017 10:53 pm
by Spectre660
The X5000 boot drive does not need any "A1 booter "so don't install anything.
xenic wrote:
Spectre660 wrote:for X5000 the boot code is on the microsd card .
(X5000 manual page 10)
In that case, what do you enter for AmigaOne boot code in the Edit RDB window of MTB??

Re: Preparing a new HD for installing 0S4.1 FE

Posted: Tue Aug 22, 2017 11:14 pm
by tonyw
xenic wrote:In that case, what do you enter for AmigaOne boot code in the Edit RDB window of MTB??
As Spectre660 said, the SLB was only used on the SEs, XEs, µA1, Sam 440s and 460s. No other platform used it and it's not required in any modern machine.

Re: Preparing a new HD for installing 0S4.1 FE

Posted: Tue Sep 05, 2017 9:05 pm
by Elwood
JosDuchIt wrote:Guidance on this? URL?
With your OS4 CD, you have an "Installation guide" that explains this, under "Harddisk setup with Media Toolbox". It should explains it for all machines with Uboot.
For machines based on Open Firmware, you may find enough information here: http://www.amedia-computer.com/amiga/do ... nglish.pdf